Related Products

HOME > Products > ADSS/OPGW Fitting > Energy > Formed Wire > Formed Wire Dead-end for Guy Wire

Product Name: Formed Wire Dead-end for Guy Wire

Product Number: 025

Product Details

Application and Function:

 

The pre-twisted guy wire tension clamp, intended to fix guy wire clamp on pole, iron tower, and microwave tower, may replace the common wedge clamp to fix guy wire on line pole.

  

Installation of Formed Wire Dead-end for Guy Wire  

 

Picture of Preformed Guy Wire Tension Clamp installation steps, product functions and applications.

 

 

Install on the ground anchor, first, install the guy wire clamps at the middle of insulator and at the end of pole

 Picture of Formed Wire Dead-end for Guy Wire installation steps, product functions and application

1.   Pull clamp through insulator, measure out about 10cm from the guy wire end, press the joint mark with thumb, begin to wind one of its legs;

 Picture of Formed Wire Dead-end for Guy Wire installation steps, product functions and applications.

2.   Wind one leg until about 2-3 pitches from the guy wire clamp, mark at the joint of both guy clamp legs, begin to wind it;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

3.   For convenience, split the last pitches of guy clamp into one or more, fasten up in place singly, increase clamp strength with thimble when the guy clamp is installed on elbow hoop;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

4.   Install elbow hoop in place, one side of elbow hoop fastening bolt should through the guy wire clamp that wrapped thimble, screw up the fastening bolt;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

5.   As shown, put the installation ring onto anchor pole, set up tightener’s hinge, tighten the guy wire in place;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

6.   Measure out a palm-length of about 8cm upward from anchor pole on guy wire, wind with tape, cut the rest of the guy wire (note: if need grounding, the guy wire end may extend into thimble of anchor pole, grounding);

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

7.   First pull thimble through anchor pole, then pull the guy wire clamp through anchor pole and fasten into thimble slot, measure out about 10cm from guy wire end, press it with thumb and mark a joint point of both legs, begin to wind one of guy wire legs;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

8.   When one leg was wound until 2-3 pitches from guy wire end, mark a joint point of the two legs, and then wind another leg until 2-3 pitches from its end;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

9.   Slowly loose the tightener’s hinge, remove tightener when the guy wire is at work;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

10.   For convenience, split the last two pitches of guy wire clamp into one or more, fasten up in place singly;

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

11.   Installation is over (note: the ring of guy wire clamp);

 Picture of Preformed Line Products (Preformed Guy Wire Tension Clamp) installation steps, product functions and applications.

12.   When the guy wire clamp is needed to adjust the guy wire tension more flexibly, it may add the adjusted clamp on ground anchor, when installing, all installations are as above except reducing configuration of thimble.

 

 

 

Install Multi Guy Wires Clamp and Ensure an Equal Tension

 

1.   After installing the first pre-twisted tension clamp, use hinge to tighten the 2nd guy wire until the installed guy wire is loosed. Retighten hinge by 2 pitches;  

2.   Other steps are as above. Note: installing multi guy wires should ensure their tension equal;  

3.   If tension clamp is needed to adjust the guy wire tension more flexible, may add the adjusted clamp on ground anchor, when installing, other installations are as above except reducing configuration of thimble;  

4.  The above steps are universal, no instruction on other specially designed clamps here. If in doubt, please contact us.  

 

 

 

Instruction:

 1.   For ensuring usage and personal security, a proper model should be selected before using;  

 2.   It is a device finely designed, for ensuring a good property, should be packed and kept in carton, handled carefully;  

 3.   It may be operated only by skilled workers who are trained specially, in no case, it may be reused or modified;  

 4.   It may be installed twice within its initial 90 days to adjust tension, and shall not be dismantled again since then. As a device with special purpose, it should be installed as instruction, and avoided from damage and deformation;  

 5.   It is just used on guy wire in a designed regulation, not be used as tool, like hauling and drawing, and shan’t be installed on odd guy wires;  

 6.   To ensure a best performance played, the guy wire tension shall be kept at least 10% or so of its rated breaking tension;  

 7.   If in doubt, please contact us.  

 

Tags: Formed Wire
Facebook Twitter Youtube
Copyright © 2011 www.opgwfitting.com All Rights Reserved.
Powered by SEO | Fiber Optic Cable